loading spinner

IOT Tremoco

New product

The IOT Tremoco module is a tiny Arduino™ Zero compatible development board with LoRaWAN™ capability built-in. It is tailored for battery powered long-range monitoring and control applications. And you can choose the transceiver to be mounted on it, either the powerful RN2483A/2903A or the least expensive RFM95W.

More details

21 Items

34,44 € tax incl.

The IOT Tremoco module is a tiny Arduino™ Zero compatible development board with LoRaWAN™ capability built-in. It is tailored for battery powered long-range monitoring and control applications. And you can choose the transceiver to be mounted on it, either the powerful RN2483A/2903A or the least expensive RFM95W.

Package content:

  • 1 x IOT Tremoco board;
  • 1 x 14way pin header strip;
  • 1 x 12way pin header strip;
  • Note: The package do not include the antenna. Choose one here.

Board Features:

  • Dimensions: 26mm x 41mm;
  • Breadboard-friendly;
  • Microcontroller: ATSAMD21G18
  • Board Supply: 3,3V up to 6V;
  • 6 Analogue pins + 1 Analogue Ref pin;
  • 14 Digital IO pins;
  • 5 PWM pins;
  • SPI / I2C / UART;
  • 1 User LED;
  • Reset Button;
  • Integrated LoRaWAM™ Class A modem RN2483A(868MHz) / RN2903A (915MHz) or the LoRa Transceiver RFM95W;
  • Integrated LDO 3,3V up to 600mA;
  • Built-in LIPO Battery Charger with status LED;
  • JST Battery Connector;
  • Micro USB connector for power and communication;
  • Open source Hardware: Watch-Hardware;
  • Open source Software for RN2483A/RN2903A: Watch-LoRaWAN Watch-Pear2Pear;
  • Open source Software for RFM95W: Watch-LoRaWAN;

LoRa Features:

  • Uses license-free ISM band;
  • Long Range (up to 15Km);
  • Low power consumption;
  • Low data-rate (from 0.3 kbps to 50 kbps depending on distance);
  • Is a secure protocol, the encryption of your information is always ensured;

Using the IOT-Tremoco board to connect your devices to the cloud is a very easy task, you can take advantage of the Arduino ecosystem to connect your sensors and put it to work in the blink of an eye.

Depending on your application requirements IOT-Tremoco can live in the same battery for years, this can be achieved if the board is left in a low power state almost all the time, and off course in the capacity of the battery. This feature brings the IOT up into another level, don't you think?

And when the power is running low, you can charge it like your smartphone, just plug in the micro USB connector and it is ready to go. There is a charge status LED that will stay ON while the battery is being charged. Well, you don't really need a battery, it will run just fine straight from the micro USB connector.

You can be as far as 15Km from the Gateway and still with coverage, this will happen in optimum conditions as free line of sight, no obstacles, etc. In an urban environment the coverage will be arround 2 - 4 Km but depends in the configuration of the urban environment.

This module was designed with the LoRaWAM™ connectivity in our minds but it also can be used to make a data link between 2 or more IOT-Tremoco boards. You can easily create a secure, low data-rate link between two nodes over a few Kms.

IOT Imagination Pinout

Loading Firmware to Board

To load firmware to the board you need to connect the it to a computer using the micro usb connector on-board. Once connected the USB also provides all the power required.

You can use the Arduino IDE to edit the code and also as the software tool to load the firmware into the board. In order to do it you have to configure the IDE for the correct target board:

- Under the menu "Tools" choose the Board "Arduino/Genuino Zero (Native USB Port)";

- Under the menu "Tools" choose the Port that corresponds to you board.

Arduino IDE - IOT Imagination

8 other products in the same category: